rflasas.blogg.se - Eprom programmer i2c spi usb

#Eprom programmer i2c spi usb serial
#Eprom programmer i2c spi usb Offline
#Eprom programmer i2c spi usb plus
#Eprom programmer i2c spi usb series

#Eprom programmer i2c spi usb Offline

SPI Flash Offline Programmer SPI Flash離線燒錄器SF600 SPI Flash In System Programmer - SPI Flash在線燒錄器SF100

High-Speed SPI Master signaling at up to 40+ MHz.

It supports multiprogramming mode (up to four). The programming speed is much higher (Up to Double) of high capacity memories as compare to TL866CS and TL866A programmer.

#Eprom programmer i2c spi usb plus

SPI EEPROM/Flash主機適配器。可用自定義Script控制Adaptor自動對EEPROM、Flash等編程、測試。 TL866II Plus USB Programmer Support 15000+IC SPI Flash NAND EEPROM 8051 MCU PIC AVR GAL.TL866II PLUS programmer is the Advance version of TL866CS and TL866A programmer. Reports as a full-speed device (12 Mbps) to USB 2.0 hosts Powered from USB, eliminating power adapters

Unobtrusively record traffic on an I2C bus General purpose signaling on I2C and/or SPI pins

#Eprom programmer i2c spi usb serial

SPI – 4 wire serial communication protocolĬonfigurable slave select polarity for master mode.

Repeated start, 10-bit addressing, and combined format Standard mode (100 kbps) and fast mode (400 kbps)īyte throughput rates are near theoretical maximums As the data sheet said rsvd, I left the data in the EEPROM untouched (=0xFF) at those addresses.Total Phase主要提供I2C/SPI Host Adaptor、I2C/SPI Protocol Analyzer、USB Protocol Analyzer、CAN Bus solution等。秉承其“Powerful & Affordable”的理念，Total Phase為全世界工程師們提供了性價比極高的主機適配器、協議分析儀等。其所有工具都同時支持Windows、Linux、Mac OX X等操作系統。

Read 0xF6 // Read MEDIA_SETTINGS As you can see, the hub reads reserved data (rsvd) many times.

Read 0xDB - 0xDD // Read SD_MMC_BUS_TIMING.

Read 0xDE - 0xF3 // Read HUB CONTROLLER CONFIGURATIONS The Aardvark I2C/SPI Host Adpater is a general-purpose host adapter used to emulate master/slave devices and program EEPROMs and Flash memory.

Read 0xA0 - 0xA7 // Read rsvd, LUN_PWR_LB, LUN_PWR_HB, rsvd.

Simple KEEProg program makes programming of the memories easy and fast Compatible with USB v.1.0,v.1.1 and v.2.0.

#Eprom programmer i2c spi usb series

Supports 24xxx series from different kind of manifacturers like Microchip, ATMEL, STMicroelectronics and etc. Read 0x00 - 0x9B // Yes, 2 times in a row USB Programmer for I2C serial EEPROM memories.Read 0xAA - 0xD7 // Read rsvd data, DEV3_ID_STR, INQ_VEN_STR, INQ_PRD_STR, DYN_NUM_LUN, LUN_DEV_MAP.Read 0x9C - 0x9F // Yes, 2 times in a row.Read 0x9C - 0x9F // Read ATT_LB/HLB/LHB/HB.Read 0xFC - 0xFF // Validate NVSTORE_SIG = "ata2".Using my logic analyzer, I get the following I2C read sequence from the hub to the EEPROM:

Also, I now have an overcurrent warning on the hub's third port (which I don't get without the EEPROM), even though nothing is connected to it (USBDN_DM3/DP3 are connected to V_USB, as suggested by Microchip). For instance, instead of the SD/MMC reader's product name being "Ultra Fast Media Reader", I get "*!*ERROR: No String Descriptor for index 2!" (using USB Device Viewer). I2C, SPI and Microwire memory interfaces are supported. I made sure to first program the default parameters in the EEPROM as described in the hub's datasheet, but now, the hub doesn't enumerate as it does when I don't connect the EEPROM to it. EEPROM memory programming was never easier CodiProg USBMK2 is an universal EEPROM tool that allows to read, edit and write various types of EEPROM memories. It takes some practice to eventually get a feel for when a good clip happens. Be patient by resting the clipper flush on the mainboard first then slowly align the metal contacts to the chipset. The most crucial step is the clipper placement onto the EEPROM contact points. Using a logic analyzer, I was able to confirm that the hub does indeed read the contents of the EEPROM ( side note: there's an error in the datasheet, NVSTORE_SIG is not "ATA2", but "ata2"). Here are the components this EEPROM Flash Bios USB Programmer comes with. Hi, I'm trying to give the USB2642 custom parameters by programming an I2C EEPROM to overwrite the hub's default parameters. USB2642 - Need help with the initial read sequence from external I2C EEPROM